Artikel Ilmiah : H1A021020 a.n. DAIVA PUTRA ARRAFI'
| NIM | H1A021020 |
|---|---|
| Namamhs | DAIVA PUTRA ARRAFI' |
| Judul Artikel | PERANCANGAN KONVERTER DC-DC (BUCK-BOOST CHOPPER) PADA SISTEM MIKROGRID PLN-PLTS STASIUN PENGISIAN BATERAI MOBIL LISTRIK |
| Abstrak (Bhs. Indonesia) | Mobil listrik merupakan kendaraan ramah lingkungan yang menggunakan motor listrik sebagai penggerak, menggantikan mesin berbahan bakar fosil. Pengisian baterai mobil listrik secara fleksibel dan ramah lingkungan dapat dilakukan dengan memanfaatkan energi dari panel surya yang dioptimalkan melalui rangkaian buck-boost chopper untuk menyesuaikan tegangan output. Penelitian ini bertujuan untuk menguji kinerja sistem buck-boost chopper yang dirancang menggunakan perangkat lunak PSIM, dengan kontrol PI dan PWM yang diprogram menggunakan Arduino, serta prototipe sistem yang dirancang menggunakan Proteus. Pada simulasi PSIM, tegangan keluaran konverter telah mencapai setpoint 24 volt untuk proses pengisian baterai. Sistem mikrogrid terdiri dari dua sumber, yaitu PLTS dan PLN, masing-masing dilengkapi MCB sebagai proteksi awal serta relay otomatis yang menghubungkan suplai PLN saat daya dari PV tidak mencukupi. Prototipe sistem dirancang menggunakan software Proteus, mencakup skematik rangkaian, desain mikrogrid, dan layout PCB. Hasil perancangan menunjukkan sistem mampu mengisi baterai dari 10% hingga 100% menggunakan modul charger boost CCCV yang mengatur arus dan tegangan pengisian sesuai karakteristik baterai lithium-ion. Baterai yang digunakan berkapasitas 440 mAh dan disusun secara seri (6S) dengan tegangan maksimum 25,2 volt, serta dilengkapi BMS untuk proteksi dan manajemen sel. |
| Abtrak (Bhs. Inggris) | Electric vehicles are environmentally friendly vehicles that use electric motors for propulsion, replacing fossil fuel engines. Battery charging for electric vehicles in an eco-friendly and flexible manner can be achieved by utilizing energy from solar panels, optimized through a buck-boost chopper to adjust the output voltage. This research aims to evaluate the performance of a buck-boost chopper system designed using PSIM software, with PI control and PWM programmed using Arduino, and a system prototype designed using Proteus. In the PSIM simulation, the output voltage of the converter successfully reached the setpoint of 24 volts for battery charging. The microgrid system consists of two power sources, PV and the utility grid (PLN), each equipped with an MCB for initial protection and an automatic relay that connects the utility supply when PV power is insufficient. The prototype system was designed using Proteus software, including the schematic circuit, microgrid design, and PCB layout. The hardware implementation showed that the system can charge the battery from 10% to 100% using a boost CCCV charger module, which regulates the charging current and voltage according to the lithium-ion battery specifications. The battery used has a capacity of 440 mAh, configured in a 6-series (6S) arrangement with a maximum voltage of 25.2 volts, and is equipped with a BMS for cell protection and management. |
| Kata kunci | Buck-boost chopper, Pulse Width Modulation (PWM), mikrokontroler ESP32, Panel Surya, Mikrogrid |
| Pembimbing 1 | Prof. Dr. Eng. Ir. Suroso, S.T., M.Eng., IPU |
| Pembimbing 2 | Ir. Daru Tri Nugroho, S.T., M.T. |
| Pembimbing 3 | |
| Tahun | 2025 |
| Jumlah Halaman | 12 |
| Tgl. Entri | 2025-05-14 10:28:45.649702 |