Artikel Ilmiah : I1B006044 a.n. HARIS BUDIMAN
| NIM | I1B006044 |
|---|---|
| Namamhs | HARIS BUDIMAN |
| Judul Artikel | PEMROGRAMAN NUMERIK EFEK MUTU BAJA PROFIL TERHADAP KAPASITAS PENAMPANG KOLOM KOMPOSIT BERPENAMPANG LINGKARAN DAN PERSEGI |
| Abstrak (Bhs. Indonesia) | Analisa kapasitas penampang kolom komposit rumit, maka dari itu analisa dilakukan secara numerik sehingga lebih efisien dan cepat. Peraturan yang digunakan untuk analisa merujuk pada peraturan SNI 03-2847-2002. Analisa dilakukan pada kolom beton bertulang dan komposit baik pada penampang lingkaran maupun persegi. Kemudian, efek penambahan mutu baja profil pada BJ 34, BJ 37, BJ 41, dan BJ 50, dapat diketahui dengan melihat hasil analisa berupa diagram interaksi kedua jenis kolom tersebut. Baja profil yang digunakan dalam studi kasus adalah WF 100x100x6x8 dan WF 428x407x35x20, oleh karena baja profil WF memiliki momen inersia arah x dan y yang berbeda, kapasitas penampang kolom ditinjau terhadap sumbu kuat dan sumbu lemah. Dari hasil analisa yang dilakukan terhadap studi kasus menunjukkan bahwa, pada kolom komposit lingkaran dengan WF 100x100x6x8 penambahan mutu baja profil memberikan penambahan kapasitas penampang pada beban aksial sebesar 10.47% sampai 13,70 %, sedangkan pada momen memberikan penambahan sebesar 7.82% sampai 10.76 %. Pada kolom komposit persegi, penambahan mutu baja profil memberikan penambahan kapasitas penampang pada aksial sebesar 10.94% sampai 14.06 %, sedangkan pada momen memberikan penambahan sebesar 8.18% sampai 9.95 %. Untuk WF 428x407x35x20 pada kolom komposit lingkaran, penambahan mutu baja profil memberikan penambahan kapasitas penampang pada beban beban aksial sebesar 31.04% sampai 37.85 %, sedangkan pada momen memberikan penambahan sebesar 25.81% sampai 34.75 %. Pada kolom komposit persegi, penambahan mutu baja profil memberikan penambahan kapasitas penampang pada beban aksial sebesar 37.85% sampai 44.33%, sedangkan pada momen memberikan penambahan sebesar 26.51% sampai 39.42 %. |
| Abtrak (Bhs. Inggris) | The analysis of column cross-section capacity is complicated. The analysis can be done in numerical way, so it will be more efficient and faster. The rule that used to the analysis is referring to the regulatory of SNI 03-2847-2002. The analysis was conducted on the reinforced concrete and composite columns in both square and circular cross section. Then, the adding quality effect of steel profiles on BJ 34, BJ 37, BJ 41 and BJ 50, can be determined by looking at the results of the analysis in the form of two types of interaction diagrams column. Steel profile that used in the case study is 100x100x6x8 WF and WF 428x407x35x20, because the WF profile steel has a moment of inertia in the different direction of x and y, the capacity of the column cross section in considering of the strong axis and weak axis. Based on the analysis of the case study, it shows that, in the circular composite columns with WF 100x100x6x8 the addition in the quality of steel profiles provide additional capacity on the sectional axial load of 10,47% to 13.70%, whereas at the moment of giving increments of 7.82% to 10.76%. In the square composite columns, the addition of quality steel profiles provide additional capacity on the axial cross-section of 10.94% to 14.06%, whereas at the moment of giving increments of 8.18% to 9.95%. For 428x407x35x20 WF composite circular column, the addition of quality steel sectional profiles provide additional capacity on the load axial load of 31.04% to 37.85%, whereas at the moment gives an addition of 25.81% to 34.75%. In the square composite columns, the addition of quality steel profiles provide additional capacity on the sectional axial load of 37.85% to 44.33%, whereas at the moment gives an addition of 26.51% to 39.42%. |
| Kata kunci | beban aksial, momen, numerik, diagram interaksi, SNI 03-2847-2002, kolom komposit. |
| Pembimbing 1 | Nanang Gunawan.,ST.MT |
| Pembimbing 2 | DR.Eng Purwanto Bekti |
| Pembimbing 3 | |
| Tahun | 2012 |
| Jumlah Halaman | 13 |
| Tgl. Entri | (belum diset) |