Artikel Ilmiah : H1D009038 a.n. MOHAMMED NURFAIZI KAMAL
| NIM | H1D009038 |
|---|---|
| Namamhs | MOHAMMED NURFAIZI KAMAL |
| Judul Artikel | PEMODELAN FISIK GAYA SERET BATU PADA ALIRAN DEBRIS |
| Abstrak (Bhs. Indonesia) | Pemodelan fisik gaya seret batu pada aliran debris untuk skala laboratorium dilakukan di laboratorium hidraulika Fakultas Teknik Universitas Jenderal Soedirman. Penelitian ini bertujuan mengetahui pengaruh gaya seret batu terhadap pergerakan batu-batu pada aliran debris, mengetahui pengaruh ukuran batu terhadap pergerakan batu akibat aliran debris, dan mengetahui pengaruh kemiringan alur terhadap kecepatan aliran debris dan pergerakan batu-batu yang terbawa. Penelitian ini diawali dengan melakukan percobaan pendahuluan. Percobaan tersebut menggunakan alat Recirculating Sediment Flume. Tujuan dari percobaan pendahuluan ini adalah untuk mengetahui kapasitas debit maksimum yang mampu diberikan oleh pompa. Data-data pengamatan pada penelitian ini diperoleh dengan membuat variasi debit air kecil, besar, hingga konstan, dan kemiringan sudut. Hasil data tersebut diolah dengan melakukan perhitungan dan analisis. Hasil pengolahan data tersebut memperoleh nilai-nilai yaitu nilai gaya seret batuan, nilai pengaruh ukuran model/ batuan, dan pengaruh kemiringan saluran terhadap aliran debris. Nilai gaya seret ini menyatakan bahwa semakin besar nilai gaya seret akan linier terhadap keadaan gerakan batu/model. Kemudian untuk perhitungan pengaruh ukuran/model batu tipe 1 (d = 0,0245 m) bergerak pada saat debit (Q = 0,1374 liter/detik) dengan waktu gulir (tg = 44,74 detik) dan kecepatan gulir (Ug = 0,096 m/s) dan untuk batu/model tipe 2 (d = 0,015 m) bergerak saat debit (Q = 0,0786 liter/detik) dengan waktu gulir (tg = 75,55 detik) dan kecepatan gulir (Ug = 0,057 m/s). Kesimpulannya, nilai pengaruh ukuran model ini menyatakan bahwa semakin kecil ukuran batu/model maka akan semakin kecil debit yang diperlukan untuk membuat batu bergerak. Selanjutnya untuk hasil perbedaan kemiringan saluran (θ = 0,4° dan θ = 1°) yaitu saat kemiringan saluran (θ = 0,4°) untuk membuat batu/model mulai bergerak dengan waktu gulir (tg = 53,84 detik) dan kecepatan gulir (Ug = 0,080 m/s) maka dibutuhkan kecepatan aliran (U = 0,075 m/s), lalu saat kemiringan saluran (θ = 1°) untuk membuat batu/model mulai bergerak dengan waktu gulir (tg = 31,21 detik) dan kecepatan gulir (Ug = 0,138 m/s) hanya dibutuhkan kecepatan aliran (U = 0,008 m/s). Dengan nilai ini dapat diinterpretasikan bahwa semakin besar sudut kemiringan saluran maka semakin mudah untuk membuat batu/model mulai bergerak dan linier terhadap waktu maupun kecepatan gulir batu/model tersebut. |
| Abtrak (Bhs. Inggris) | A physical modeling of drag force of rock on the debris flow in laboratory scale have been done at hydraulics laboratory of Civil Engineering Faculty, Jenderal Sudirman University. The aims of the research is to determine of the movement drag force of rock boulders on debris flow, determine the size effect of the rocks on the movement due to debris flow, determine the effect of the channel slope on debris flow velocity and the movement of rocks carried. The beginning of this research have done with a preliminary experiment. The experiment using a Sediment Recirculating Flume. The purpose of this preliminary experiment is to determine the maximum discharge capacity capable given by the pump. The data observations in this research was obtained by varying the water discharge small, large, up to a constant, and tilt angle. The results of the data is processed by performing calculations and analysis. The results of the data processing to obtain the values of rock drag force, the value of the effect size of the model / rock, and the effect of the channel slope to debris flow. These value of drag force that claim the greater drag force value will be linear with respect to the state of rock movement / model. Then for the calculation of the effect of size / model of rock type 1 (d = 0.0245 m) moving at the time of discharge (Q = 0.1374 liters / sec) with a scroll (tg = 44.74 sec) and scroll speed (Ug = 0.096 m / s) and for the rock / model of type 2 (d = 0.015 m) moves while the discharge (Q = 0.0786 liters / sec) with a scroll (tg = 75.55 sec) and scroll speed (Ug = 0.057 m / s). In conclusion, the value of the effect size of this model suggests that the smaller the size of the stone / models will be smaller discharge necessary to make the stone move. Further to the results of channel slope difference (θ = 0.4 ° and θ = 1 °), namely when the slope of the line (θ = 0.4 °) to make the stone / model starts moving with a scroll (tg = 53.84 seconds) and the scroll speed (Ug = 0.080 m / s) is required flow velocity (U = 0.075 m / s). then when the slope of the line (θ = 1 °) to make the stone / model starts moving with a scroll (tg = 31.21 sec) and scroll speed (Ug = 0.138 m / s) needed only flow velocity (U = 0.008 m / s ). This value can be interpreted that the greater the angle of the channel it is increasingly easy to make rock / model starts moving and linear with respect to time and the speed of the scroll stone / model. |
| Kata kunci | Aliran debris, Recirculating Sediment Flume, gaya seret, model fisik |
| Pembimbing 1 | Wahyu Widiyanto.,S.T.,M.T. |
| Pembimbing 2 | Dr.Eng. Purwanto Bekti S.,S.T.,M.T. |
| Pembimbing 3 | |
| Tahun | 2015 |
| Jumlah Halaman | 18 |
| Tgl. Entri | 2015-05-13 20:25:36.79188 |